| Number |
|
Part |
Price |
| S-9522K |
 |
Bowl plug kit - all 3 plugs with gaskets |
$15.95 |
| S-9563K |
 |
Bowl plug gaskets (pack of 10) |
$3.95 |
| S-9526K-97 |
 |
Accelerator pump rod for 97 and 81 - stainless steel |
$15.95 |
| S-9526K-48 |
 |
Accelerator pump rod for 40 and 48 - stainless steel |
$15.95 |
| S-9531K |
 |
Accelerator pump lever, spring & cotter pin - stainless steel |
$15.95 |
| S-9533K-size |
 |
Main jets - pair - all sizes available |
$7.50 |
| S-9534K |
 |
Emulsion tubes - pair |
$19.95 |
| S-9537K |
 |
Choke lever detent plunger & spring - stainless steel |
$3.95 |
| S-9541K |
 |
Idle adjusting screws & springs - pair |
$9.95 |
| S-9542K |
 |
Idle jets - pair |
$15.95 |
| S-9546K |
 |
Choke shaft kit inc. lever, washer, screw & end stud |
$15.95 |
| S-9549K |
 |
Choke plate kit inc. screws - stainless steel plate with correct 15 deg edge |
$9.95 |
| S-9550K |
 |
Stromberg Superfloat™ with new float pin |
$19.95 |
| S-9552K |
 |
Throttle kicker assembly (stainless steel) inc. idle screw & spring |
$19.95 |
| S-9558K |
 |
Float pin |
$4.95 |
| S-9564K |
 |
Fuel inlet S-jet with gasket |
$15.95 |
| S-9573K |
 |
Accelerator pump check valve |
$4.95 |
| S-9577K |
 |
Accelerator pump discharge jet plus collar - per pair |
$15.95 |
| S-9581K |
 |
Throttle shaft and lever kit inc. screws & bushes - stock size |
$29.95 |
| S-9585K |
 |
Throttle plate - 7 degree edge - pair |
$9.95 |
| S-9586K |
 |
Throttle/choke plate screw kit - pack of 10 |
$3.95 |
| S-9589K |
 |
Throttle stop screw & spring - stainless steel |
$4.95 |
| S-9592K |
 |
Choke & accelerator pump lever fulcrum screws |
$9.95 |
| S-9594K |
 |
Power by-pass jet with gasket
- all sizes available |
$9.95 |
| S-9630K |
 |
Accelerator pump kit inc. springs/retainers/washers/felt gasket/cotter pin |
$15.95 |
| S-9631K |
 |
Accelerator pump - stainless steel rod |
$7.50 |
| S-31095K |
 |
Body screw kit - 8 screws/washers - stainless steel |
$9.95 |
| S-9590K-97 |
 |
Premium Service Kit kit for Stromberg 97, 48 and 40 - Full gasket kit, ‘No-stick’ S-jet inlet valve, Accelerator pump check valve, 2 idle mixture screws and springs, Full accelerator pump kit, Installation sheet and float gauge (over US$55 retail value) |
$39.95 |
| S-9571K |
 |
Spring kit - all exterior springs - all stainless except idle adjuster springs |
$9.95 |
| S-9447K |
 |
Full gasket kit - three main gaskets (non-paper), plus felt gasket for accelerator pump, and ring gaskets for power jet, inlet valve and drain plugs |
$9.95 |
| S-9447K-5 |
 |
Bulk gasket kit as above x 5 |
$39.95 |
| S-69447K |
 |
Carb to manifold gasket pack. 6 gaskets |
$11.95 |
| S-89067K-3 |
 |
Manifold stud kit. 3 studs with stainless lock washers and nuts |
$11.95 |
| S-89067K-4 |
 |
Manifold stud kit. 4 studs with stainless lock washers and nuts |
$15.95 |
| S-29447K |
 |
Carb blank off plate. Want to keep a carb or two out of action? Slip this thin stainless plate between the carb and gasket. It's shaped to fit the later 1-1 base footprint you find on most '50's and '60's 2-bbl manifolds, but it's smaller so it all but disappears |
$11.95 |
| S-9552K-C |
 |
A perfect replica - in stainless - of the late model 97 throttle kicker assembly for cable choke (designed for '49-on Fords). A separate bracket - included - mounts off the rear body screw to hold the cable sleeve. |
$39.95 |
|
|
|
|
on every part. 
